Crate | TX50DB | Specifications | Crate TX50DB Specifications strongly urge you to go over the information contained in this manual before you begin playing. Does anybody have schematic for this battery-powered amplifier? And what is the difference between Crate TX50DB and Crate TX50 Limo?. 2 Answers. Need amp schematic for a Crate model vc Web page with schematics and requests:
|Published (Last):||7 February 2015|
|PDF File Size:||2.47 Mb|
|ePub File Size:||5.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
These limits are designed to provide reasonable protection against harmful interference in a residential installation. Connect a tape player for sound tracks and back up music to the CD Input jacks. Plug the small round connector of the supplied AC wall adapter into this jack to tx50vb the internal battery. Crate amplifiers stereo chorus amp operation manual 4 pages.
Crate TX50DB Manuals
Use this control to adjust the tone of the instrument channel 1. This high-Z input works with all types of pickups, from Piezo to active types.
The TX50D can be used in a variety of different ways, some of which are shown below and on the following page. The LED will change to red when the battery is low and needs recharging. The TX50D may also be powered by using a volt vehicle cigarette lighter adapter, available at most electronic supply stores. Answer questions, earn points and help others Answer questions. Never spray cleaning agents directly onto manaul cabinet, and stay away from abrasive cleansers which could damage the finish.
Please assign your manual to a product: At last, you can take your music with you and have great tone on the road.
Crate LIMO TX50D Driver Manual
Connect craye low impedance microphone to the Low Z jack. Since this appears to be a guitar amp that expects a floating input plug any connection at the input to say, a mixer etc may cause a re-grounding via that equipment’s circuits, thus negating the auto mute Use this control to adjust the mid frequency level for the instrument channel 2.
Are you a Crate Music Expert? Use this control to adjust the amount of signal sent to the internal Digital Signal Processor DSP for the instrument channel. Crate Music Posted on Jun 02, Be the first to answer. The charger can also function as an AC power supply. Not only is crte TX50D compact and portable, it also sports two separate channels and the incredible sound that has made Crate a household name among musicians.
Use this control to adjust the mid frequency level for the mic channel. The amp pops anytime i turn the volume knob.
Use this control to adjust the gain for the instrument channel 1 — the lower the setting, the lower the amount of distortion. Chorus combined with large reverb 22 23 24 ROOM: Damage to the amplifier may occur!
Connect a high impedance microphone to the Instrument Input jack. It is stamped on the old fuse or will be written on the rear panel or type plate. The battery fully recharges within 6 hours, providing up to 8 hours of use at low levels, about 4 hours of use at moderate levels, and about 2 hours of use at continuous full power sine wave. Use this control to adjust the output level of the instrument channel 1. Idea 3 — Sing along: The battery is rated for up to charging cycles.
Crate TX50DB Manuals
Use this control to adjust the low frequency level for the instrument channel 2. The battery inside the TX50D must be fully charged before operating the amplifier for the first time. If the battery is drained too low, the Power LED will go out.
This LED illuminates yellow when the power switch is at the on position — when the amp is fully charged. Connect a low impedance micro- phone here by means of a shielded signal cable terminated with an XLR type connector. Xrate you tried turning Gain1 and Gain 2 or the Clean Channel volume?
Use this switch to turn the amplifier on top of the switch depressed and off bottom of switch depressed. Ask a Question Usually answered in minutes!
Use these jacks frate connect the outputs of a CD player or tape player to the amplifier. Idea 1 — Play and sing, with external effects and backup: Use this control to adjust the low frequency level for the mic channel.