Buy BS EN TESTING FRESH CONCRETE – PART 1: SAMPLING from SAI Global. said in BS EN , take a few samples throughout the pour for the best representation of the batch and make sure you take % of what you think you’ll . This British Standard specifies two procedures for sampling fresh concrete which are implemented by composite sampling and by spot.
|Country:||United Arab Emirates|
|Published (Last):||17 February 2017|
|PDF File Size:||19.77 Mb|
|ePub File Size:||14.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
What is the time limit before placing of fresh concrete? See more standards on testing concrete.
Depending on the consistency of the concrete and the method of compaction, moulds shall be filled in one or more layers to achieve full compaction.
Document Status Indicators The Green document status indicator indicates that the document is: Strike off the mold with the tamping rod in a screeding and rolling motion Remove concrete from the area surrounding the base to prevent interference with the movement of slumping concrete.
Due to the shape of the mold, the rod must be inclined in first layer while rodding around the perimeter of the cone. Scope This standard covers the determination of the temperature of freshly mixed hydraulic-cement concrete.
Please first log in with a verified email before subscribing to alerts. Sampling Concrete It is acceptable to measure the temperature in: Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects.
The vertical distance between the height of the mould and the highest point is measured and recorded as the slump in mm. Metallic, Frustum of a cone Alternative materials are allowed if requirements are met comparability tests Tamping Rod Round, straight steel rod, length mm and diameter 16mm Tamping end rounded to a hemispherical tip Measuring Device Ruler Marked in increments of 5 mm or smaller Length of at least mm In addition, a scoop is needed.
Materials handling, Test specimens, Sampling methods, Concretes, Samples, Cement and concrete technology. The requirement for remixing the sample before tests on the fresh concrete, or before making test specimens, is included in the relevant standards. If the document is revised or amended, you will be notified by email. Sampling BS EN specifies two procedures for sampling fresh concrete, by composite sampling and by spot sampling.
Concrete cubes at the site Marking The test specimens shall be marked clearly and indelibly, without damaging the specimen using a cub tag that contains the information related to the specimen Casting date, ticket number, specimen ID, location of sampling…. Pack the hardened test specimens in wet sand or wet sawdust or wet cloths wet burlapor sealed in plastic bags containing water. Want access to British Standards?
After compaction of each layer, tap the sides of the container smartly with the mallet until large bubbles of air cease to appear on the surface and depressions left by the compacting rod or bar, are removed. Records shall be kept to ensure the traceability of the specimen from sampling to testing.
Sampling of Freshly Mixed Concrete at the Field (BS EN ) – QA/QC Construction
This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Where required, the specification of a maximum time between placing layers of concrete should take account of the likely temperature of the concrete, cement type, mix proportions, the use of admixtures with set retarding properties and consistency of the concrete. The elapsed time shall not exceed 15 min.
Avoid over-vibration, which may cause loss of entrained air. Move the scoop around the perimeter of the mold to ensure even distribution of material and minimize segregation.
Notify me of new comments via email. Full compaction is achieved using mechanical vibration, when there no further appearance of large air bubbles on the surface of the concrete and the surface becomes relatively smooth with a glazed appearance, without excessive segregation.
Protect the sample from the sun, wind, and other sources of rapid evaporation, and from contamination. Report from the sample includes: This will cause the delay of pouring and worst the ns of other concrete truck loads because of the temperature overdue.
BS EN – Testing fresh concrete. Sampling (British Standard)
Fill the mold in three layers of approximately equal height. Both parties will agree to the specific time limit as substantiated from the concrete design mix. Accept and continue Learn more about the cookies we use and how to change 12350–1 settings. To find out more, including how to control cookies, see here: Rod the second and top layers throughout their depth, so that the strokes just penetrate into the immediately underlying layer.
Do not remove the device from the concrete when reading the temperature. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.
Click here to find out how to access this document.
Again there may be more recent versions of the document. You are commenting using your WordPress. By continuing to use this website, you agree to their use.
Frequency shall be at least vibrations per minute The diameter of the internal vibrator not exceeding one-quarter of the smallest dimension of the test specimen Vibrating table with a minimum frequency of 40 Hz 2 cycles per minute Compacting rod or bar Preparation and filling of the moulds Before filling the mould, cover the inner surface of the mould with a thin film non-reactive release material to prevent the concrete from adhering to the mould.
The faster, easier way to work with standards. Gently press the concrete around the TMD at the surface of concrete so that the ambient temperature does not influence the reading.
BS EN 12350-1:2009