Brand new Bosch RP17PT Tankless Water Heaters at Wholesale Prices & Free Shipping – Returning Customers get Extra 15% Off by using our Free VIP. Find great deals for Bosch RP17PT Electric Tankless Water Heater v. Shop with confidence on eBay!. Bosch Thermotechnology Corp. 50 Wentworth Avenue, Londonderry, NH – Important Safety Instructions When using this electrical.
|Published (Last):||12 March 2012|
|PDF File Size:||4.32 Mb|
|ePub File Size:||13.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
You can also call Bosch Thermotechnology Corp. This water heater is designed for a cold water feed only. Answered on Feb 07, Any Component Part Other Than the Heating Modules — If any other component part other rpp17pt the heating modules proves to be defective in material or workmanship within one 1 year from the date of original installation of the water heater, Bosch Thermotechnology Corp.
Answered on Nov 27, Open all hot water taps supplied by the heater.
Bosch RP17PT Electric Tankless Water Heater 240v
Please login or register before adding a question. Could this be the problem? If thermal cut out does not reset, check for continuity through each cutout Less than 0.
One or more of the heating module thermal cut-outs has tripped Turn off the power to the heater, remove the cover and locate thermal cutouts on the top of each heating module. Cold water only — Neon light off Flow rate is too low Verify the flow rate out of fixture is at or above the minimum activation rate required for the unit to activate.
IMPORTANT When the heater is not within sight of the electrical circuit breakers, a circuit breaker lockout or additional local means of disconnection for all non-grounded conductors must be provided that is within sight of the appliance.
Heater must be full of water and air purged before power is turned on. No electricity at the heater or one of the supplies has failed Have a licensed fp17pt verify proper wiring and adequate voltage on the terminal block inside the water heater. See Graph 1 on Page 8 of this manual. One of the power supplies ro17pt not on Have a licensed electrician verify adequate voltage on the terminal block inside the water heater.
Shut off all hot water taps. Posted by Global ProTankless Supply at 1: I did order a Pelican NS-3 water filter no bags of salt requiredalong with a red extra post filter on it, to bsoch sure I complied with the yr specifications required in the tankless warranty. Use of an isolation valve on the hot water outlet to control flow rate is recommended.
Reconnect the water supply to the inlet of the unit marked blue.
Bosch RP17PT Specifications |
Damage caused by exposure to freezing conditions is not covered by the warranty. Inlet water temperature is too warm Verify the heater is being feed with cold water only. In the Commonwealth of Massachusetts a licensed plumber or electrician must perform the installation.
Wait until you are sure that it has completely thawed out. And that’s it turn on the gas and water and go test your brand new water heater!
rp17ptt Bosch operating instruction water heater hx lp and hx ng 18 pages. There are internal safety thermal cut-outs which will trip if the unit overheats.
Under no circumstances should the heater be mounted differently. Answered on Jan 21, Now you can have an endless supply of hot water without the devastating impact on your electric bill.
Automatic instantaneous type water heaters for use with natural and liquefied petroleum gas 24 pages. Disconnect this product from the electrical supply before cleaning, servicing or removing the cover. Not finding what you are looking for? If you are not comfortable or qualified to perform this task, consult the original installer or a licensed electrician.
If readings are different than listed specifications on Page 14, contact Technical Support for further instruction. Do not switch the heater on if you suspect that it may be frozen.
20 Most Recent Bosch RP17PT Whole House Electric Questions & Answers – Fixya
See the technical support section of www. It is plenty hot and I have to turn on the jets for a minute to cool it some before I get in. The person who initially installed the unit is the best one to contact for help.
When trying to ignite the water surges, doesnt get hot.
Graph 1 8 For example: Maximum output 15kW at V Enter text from picture: Close installer supplied cold water shut off valve if none installed, install before proceeding. Also it doesn’t hurt to go over everything with some soapy water in a sprayer to check for gas leaks especially if unit is old or if you can smell gas, I imagine if there was a gas leak inside the cover that would cause bpsch issues. What do I do?