BC557 SMD DATASHEET PDF

BC ON Semiconductor / Fairchild Bipolar Transistors – BJT PNP V mA HFE/ datasheet, inventory, & pricing. BC BC VCEO. − − − Vdc. Collector – Base Voltage. BC BC BC dimensions section on page 6 of this data sheet. ORDERING. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Of the above types common emitter type is the popular and mostly used configuration.

As discussed a transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. The value of this resistor R B can be calculated using below formulae.

Some of the configurations used in amplifier circuits are Common emitter amplifier Common collector amplifier Common base amplifier Of the above types common emitter type is the popular and mostly used configuration. TL — Programmable Reference Voltage. Amplifier modules like Audio amplifiers, signal Amplifier etc.

Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin. If you are designing a PCD or Perf board with this component then the following picture from the Datasheft Datasheet will be useful to know its package type and dimensions.

bc SMD datasheet & applicatoin notes – Datasheet Archive

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. Please enter a valid Pincode.

When this transistor is fully biased then eatasheet can datsaheet a maximum of mA to flow across the collector and emitter. Current flows in through collector. BC Transistor as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

CD is a NPN Transistor that should be considered for use in design circuits requiring general p.

BC557 Datasheet, Equivalent, Cross Reference Search

HTML is not translated! Qty Check For Your Pincode: BFR91 should be considered to be used primarily for design of high-gain, low noise, small-signal amp. The device consists o. CD is a PNP Transistor that should be considered for use in design circuits requiring general pu. Detailed datasheet datahseet the device can be downloaded from the Documents section.

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. The device is available in a TO package.

Complete Technical Details can be found at the BC datasheet given at the end of this page. Submitted by admin on 26 October Description BC is a PNP Transistor in SOT23 plastic package that should be considered for use in design circuits requiring general purpose switching and amplification. A Transistors acts as an Amplifier when operating in Active Region. TO Thermal Conduction Transistor Silicone Insulation Pad Electrically isolates transistor or other components from the heat-sink to make thermal conduction b.

It can amplify power, voltage and current at different configurations. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

Electrically isolates transistor or other components from the heat-sink to make thermal conduction b. BC is a general purpose NPN transistor which should be considered for use in design circuits requ.

As mentioned the biasing bc55 should maximum of 5mA. BC is a PNP Transistor in SOT23 plastic package that should be considered for use in design circuits requiring general purpose switching and amplification. BC is a PNP Transistor that should be considered for use in design circuits requiring general pur. Features Description Documentation Reviews 0.

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. The transistor can be used for sms.

IRFZ44 is N-channel enhancement mode standard level field-effect power transistor in a plastic envel. Current Drains out through emitter. The combo comprises of TO package heat sink, thermal conductive silicon insulation pad, nut, ins.